STOVE PIPE GUN JAM HOW TO
STOVE PIPE GUN JAM PLUS

Lighter loads require lighter springs, hotter loads require a stiffer spring. However, if the problem repeats itself, then you may have a mechanical issue.įirst, make sure that you're using an appropriate recoil spring weight for your ammunition. If the problem doesn't repeat itself, it's possible that it was a bad round which does happen. Tightening the grip and ensuring you aren't short-stroking the slide with the thumb or anything else will rule out these causes in short order. At that point, you must diagnose what the cause of the stovepipe was. When a stovepipe happens, you pull back the slide to get the round free. This holds it up in the ejection port and causes a stovepipe. If the extractor is worn down, or if it does not have sufficient tension, the round will not be pulled from the chamber and ejected with sufficient force. The extractor is also a cause of stovepipes. Riding the thumb too high on the slide will also interfere with the pistol cycling and lead to a stovepipe. Limp-wristing can also cause a stovepipe, as not holding the pistol firmly enough can cause the slide to not cycle correctly, leading to a shorter return stroke and a stovepipe. If ammunition is the cause, either use a more appropriate load or cease using faulty rounds. If you're using a recoil spring with too much tension for the ammunition you're using, the slide will cycle faster than the spent case is sent out the ejection port. This could be due to switching to lower-pressure rounds, a bad batch of factory ammunition or a poor handload.Īnother common cause is the recoil spring. Diagnosing And Fixing A Stovepipeįirst, if the ammunition you're using has too weak a powder charge, it won't cycle the slide correctly. In the latter instance, the round just didn't get pulled out of the chamber after firing.Įach has their own causes and fixes. It looks like a stove pipe is sticking out of the chamber and thus you get the name. In the former instance, the round will get stuck between the slide and the barrel throat while ejecting, due to the slide cycling too fast or too slow an ejection. The revolver crowd doesn't deal with it as much, though an ejector can certainly get break. Just like a failure to feed, this is an issue that pretty much only affects semi-autos. In the latter case, a round is fired but isn't extracted out of the chamber. There is a stovepipe, where a spent case gets caught in the ejection port, and a failure to extract. There are two basic types of failure to extract. That said, let's find out a bit more about failures to eject. The good news is that the cause is usually rather minor and can be addressed in a matter of minutes. Just like a failure to feed, the cause can be diagnosed and addressed. A failure to eject, otherwise known as a FTE, can take a few different forms and has several common causes.

There are a few common firearm malfunctions, one of the chief among them is a failure to eject, where a spent case is not ejected from the pistol and keeps the slide from cycling.

STOVE PIPE GUN JAM HOW TO

I have put just over 300 rounds of Federal Auto Match and 100 Winchester Target through that modified magazine with NO stove piping at all even with rapid fire.Why You Had A Failure To Eject And How To Fix It That steel casting is as hard as nails by the way. I made sure I maintained the angle so as to leave material there to retain the cartridge in the magazine.

So what I decided to do was use one mag as a sacrificial lamb and carefully grind that lip off. The ejector in the bolt is for when there is no mag installed. Now somewhere on here or maybe another site I read that the lip on the magazine was the main ejector and after observing the bolt when pulling it back it certainly is.I made sure the mag was fitting snug and secure as well. I even ran some Remington dirty bulk with the same results.

STOVE PIPE GUN JAM PLUS

I then installed an extractor and a Spartan charging handle plus the poly bolt buffer that I bought from TK.Īll this brought me down to 10% of my cartridges stove piping.Ĭartridges used have been CCI, CCI Mini Mags, Blazer, Winchester target black box, Federal Auto Match with the same results for them all. I have buffed, polished and basically cleaned up all the rough surfaces. I have spent many hours reading here and got a ton of tips and ideas.

I love it for its light weight and its accuracy.īUT I have had this nagging issue of 25% of my rounds stove piping. I recently purchased a slightly used Ruger 10/22 carbine with a BX trigger.

Stove pipe gun jam